RO Repair & Water Tank Cleaning — Samastipur & Nalanda | 7903760419
Home › Blog › TDS Guide
RO Guide — Samastipur & Nalanda

TDS in Drinking Water — What the Numbers Mean & What to Do

November 2026Repair Guru SPJ7 min readSamastipur & Nalanda
🧮

A TDS meter is the most useful RO tool you can own for a few hundred rupees, and the most misunderstood. This guide explains what the number is, what it cannot tell you, and a simple formula that shows whether your RO membrane is still working.

Want your tap and RO water TDS checked?

Call 7903760419 or WhatsApp us. See the full service page: RO Repair in Samastipur.

What TDS Actually Is

TDS (total dissolved solids) is the amount of dissolved minerals and salts in water, shown in mg/L, which is roughly the same as ppm. A meter does not count them directly. It measures how well the water conducts electricity and converts that into a number.

The Official Limits

ParameterBIS acceptable limit
TDS500 mg/L (up to 2,000 mg/L allowed only where no better source exists)
Fluoride1.0 mg/L (1.5 mg/L where no alternate source)
Arsenic0.01 mg/L

Source: BIS IS 10500:2012. Always check the current standard; this is a summary, not a legal reference.

Reading Your Tap Water

Tap TDSWhat it usually meansSensible next step
Below 150Low in dissolved saltsRO is mainly for contaminants, not TDS. Test for them.
150 – 500Within the BIS acceptable limitRO with a TDS controller keeps taste balanced.
500 – 2,000Above the acceptable limitRO membrane recommended.
Above 2,000Very highAsk a technician; an RO may struggle. Get a lab test.

The Rejection Formula

1

Measure input and output

Test tap water, then the purified water from the RO tap. Rinse the meter probe between readings.

Step 1Can try yourself
2

Apply the formula

Rejection % = (input − output) ÷ input × 100. Example: tap 600, output 40 → (560 ÷ 600) × 100 = 93%.

Step 2Can try yourself
3

Judge the result

A healthy membrane usually rejects the large majority of dissolved solids, often 90% or more. If it has fallen well below what it was when new, the membrane is losing performance.

Step 3Can try yourself
4

Allow for a TDS controller

Many ROs blend some tap water back in for taste. That raises the output reading by design, so compare against your own earlier readings rather than a fixed number.

Step 4

What a TDS Meter Cannot Tell You

It cannot detect arsenic, fluoride, bacteria, pesticides or nitrate. Bihar's PHED lists Samastipur as arsenic-affected and Nalanda as fluoride-affected, which is why TDS alone is not enough in either district and a lab test is the only way to know your own water. Source: Bihar PHED — Water Quality.

Frequently Asked Questions

What TDS should RO purified water show?

It depends on your tap water and whether the RO blends water back. Track your own readings over time; a sudden rise points to filters or the membrane.

Is very low TDS water bad?

Very low TDS water tastes flat to some people. If you prefer more taste, ask the technician to adjust the TDS controller, but keep it conservative where arsenic or fluoride is a concern.

Can a TDS meter be wrong?

Yes, if the probe is dirty or the battery is weak. Check it in clean water first and repeat the reading.

Do you check TDS during a visit?

Yes — input and output TDS is part of every RO inspection.

Get Your TDS Checked and Your RO Tested

Inspection ₹99 · Replace only what is worn · 30-Day Warranty

Tags: TDS in drinking water TDS meter RO TDS RO repair Samastipur RO repair Nalanda

Related Articles

Call NowWhatsApp